Are you looking for:

Scorpion Jack TJ12 Stationary 25,000 lb. capacity Truck Jack

The Scorpion Installed In-Ground lift is semi-recessed in your shop floor. This is a semi-inground installation is an ideal solution for those shops that perform a lot of tire service and Brake Service. This is an installed version of the ScorpionTJ12 service jack and it offers a perfect combination of speed, efficiency, ease of use and value. The Scorpion Installed lifts are much less expensive than your standard above- ground options or for that matter the in-ground options too.


These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi). So you lift the whole front end or axle assembly in one go. There is a tire spotting dish for quick set up, and a remote control to allow the operator to check the load.


There is a built in lock for safety and other convenience features.


The lifts come with a control station housing the pump unit and a 20 Ft. Remote control so the operator can spot the load.


Features:

  • 25,000 Lb capacity
  • Dual hydraulic rams for lifting
  • Lift over 20" with a built in safety lock
  • Lift across the axle with the lifting saddles or lift on the frame
  • Heavy-duty hydraulics and air motor

  • Choose between:

  • Above Ground install - 8" Driver Over Height
  • Semi In-Ground install - 4.25" Drive Over Height
  • In-Ground Install - Flush mount with 0" Driver Over Height
  • Diamond Tread Aluminum Topsider Truck Box Series - 16" x 13" x 72"
  • Large 12" tall door opening and the recessed door frame provide easy access to spacious storage area
  • Full-length continuous hinge on doors offers a sturdy, durable and smooth performance
  • Heavy-duty steel support legs mount directly into bed floor, not into fender
  • Contractor grade diamond bright tread aluminum box
  • Thick 3" wide rubber pad protects truck side rail
  • No drilling in side rail; J-bolts fasten under bed lip
  • Stainless steel die cast T-handle compression latch with lock for security
  • Full-weather stripping keeps moisture and dust out
  • Individually boxed for shipping
  • Two doors

  • Buyers # 1701551

    H x D x W Size: 16" x 13" x 72"

    Dayton & Dual Wheel Adapter for Big Truck Tire Step - (Adapter Bar Only)

    The 5950 Dual Wheel Adapter must be used when using the Big Truck Tire Step on Dayton and dual wheels.

    This adapter provides extra stability by resting against the tire when there is no rim to rest against. The Dual Wheel Adapter is included with the 5800 Super Single 2-Step and the 5300 Super Single 3-Step.

    The Dual Wheel Adapter can be easily attached to any Big Truck Tire Step by sliding the adapter’s two attachment posts over the step’s rear stabilizing posts. Secure the adapter with the included screws and nuts.

    Super Single Model numbers 5800 and 5300 come pre-drilled for the adapter. If using the dual wheel adapter with model numbers 5500 or 5100 you must: 1) Remove vinyl caps. 2) Slide on adapter and mark hole placement. 3) Drill holes in the stabilizing posts. 4) Attach Dual Wheel Adapter.

    *Note: This is the adapter bar only. Steps are sold separately.

    7.5HP 80 Gallon Vertical Two Stage Electric Air Compressor

    Features and Benefits:

    • Start-Stop pressure switch control
    • ASME safety valves fully-enclosed belt guard
    • Tank drain and discharge valve
    • 208-230 volt, single phase
    • 2 year full warranty

    This compressor comes complete with everything you need to optimize your work and minimize down time. 25.3 cfm @ 100 PSI.

    Crib Stand Set (includes 12501, 12502, and 12503)
    Makes lifting easier Included in the set are ESCO part numbers: 12501 - 3" heavy duty steel 12502 - 6" heavy duty steel 12503 - 9" heavy duty steel All pieces in set interlock can be used individually or stacked together for various lift heights. They will not slide or shift during lifting. Maximum capacity 55 tons.
    Loading...